If your furnace won’t start after power outage, Columbus, OH, first confirm the power is back, then check the furnace breaker, the furnace power switch, and the thermostat. Most post-outage no-heat calls are fixed by one of those three checks. If it still won’t start, call our 24/7 emergency line at (380) 273-8167.
Table of Contents
Did the power actually come back?
When a furnace won’t start after power outage, Columbus, OH, start with the whole house, not the furnace. If the lights, fridge, and outlets are still dead, the outage is not over — the furnace cannot run without power. Check the outage map and restoration updates from AEP Ohio, the electric utility for most of Columbus, before you touch anything. If the lights are back but you still have a furnace not working after the power returns, the fault is inside your home. If your neighbors have power and you do not, check your main breaker — but never open the meter box or touch a damaged service line.
Which breaker runs the furnace, and how do I reset it safely?
When a furnace won’t start after power outage, Columbus, OH, a tripped breaker is the most common cause. Power surges when the grid comes back can trip the furnace breaker. Open your electrical panel and look for a breaker labelled “furnace,” “heating,” “HVAC,” or “air handler” — usually a single 15- or 20-amp breaker. A tripped breaker sits halfway between ON and OFF. To reset it, push it firmly to OFF first, then back to ON. If the breaker is fine and you still have a furnace not turning on at all after an outage, move on to the power switch below.
If the breaker trips again right away, stop — do not hold it on or tape it in place. A breaker that trips repeatedly is warning you about a short or a failed part, and forcing it can start a fire. If the panel is wet or smells burnt, leave it alone and call for help.

Is the furnace power switch on?
If your furnace won’t start after power outage, Columbus, OH, check the power switch next. Every gas furnace has a power switch that looks like an ordinary light switch — usually red, mounted on the wall near the furnace or on the unit itself. It gets flipped off by accident more often than people think: during outage clean-up, or by someone who mistook it for a light. Make sure it is ON, then listen for the small inducer fan. Also check the blower door: if the lower door is even slightly ajar, the door safety switch cuts power to the whole unit.
Why is my thermostat blank after the power came back?
A blank thermostat is the most common sight after an outage. First, check the batteries — many thermostats run on batteries, and a power cut is often the moment weak batteries finally die. Put in fresh batteries, then check the settings: mode set to HEAT, the temperature at least 3 degrees above the room temperature, and the fan set to AUTO. Smart thermostats can take a few minutes to reboot, so give it five minutes. If this is the first time turning your furnace on in the fall, check the filter and vents too — a clogged filter can keep a furnace from heating.
If your furnace won’t start after power outage, Columbus, OH, and the thermostat is still blank after fresh batteries and a correct breaker and switch, the furnace may not be sending it power — that points to a blown fuse or a control board problem, and it is time to call. If the furnace runs but only blows cold air, see our guide to a furnace blowing cold air.
Outage tip: Before you reset anything, look through the furnace sight glass and count the red blinks between pauses — then photograph the code chart sticker inside the blower door. That blink count tells a technician exactly where the furnace stopped.

The furnace clicks or the light is blinking — what does that mean?
If your furnace won’t start after power outage, Columbus, OH, and it clicks or tries to start and stops, the furnace has power but is failing a safety check. Look through the small sight glass on the blower door and count the red blinks between pauses — that pattern is a fault code, and our guide to the blinking red light on your furnace explains what each pattern means. Your code chart, the sticker inside the blower door, has the final word, because codes differ between brands.
Try one reset only: turn the furnace power switch off, wait a full 30 seconds, and turn it back on. If the same code comes back, stop resetting — repeated resets can damage the ignitor. Never bypass a safety switch to force the furnace to run. A dirty flame sensor is a common cause of burners that light and die — flame sensor cleaning and replacement usually fixes that — but a furnace keeps shutting off after a reset needs a technician.
Could the outage have damaged the furnace?
It is possible. When a furnace won’t start after power outage, Columbus, OH, a surge is one possible cause: power returning can stress the control board, the transformer, or the inducer motor, and an outage can leave the furnace locked out on a safety fault. That does not mean the furnace is ruined: a technician can test the board and the low-voltage transformer before recommending any repair. A furnace that is completely dead after the breaker and switch are confirmed may have a power supply problem, while one that runs the fan but never lights may have an ignition or safety problem — only a technician can confirm which.
Do not open the furnace cabinet to inspect the board yourself — there is live 120-volt power inside even when the furnace looks dead. If the furnace is old or the repair cost approaches replacement, ask about furnace replacement in Columbus, OH — and if you do replace, our furnace installation in Columbus, OH team can help, including advice on what size furnace do I need.

When should I call for emergency furnace help?
Call our 24/7 emergency furnace repair in Columbus, OH line at (380) 273-8167 if your furnace won’t start after power outage, Columbus, OH, even after the breaker, switch, and thermostat checks, if the breaker trips again, or if the same fault code returns after one reset. Do not wait until morning if the house is cooling fast, or if anyone in the home is elderly, very young, or has a health condition. For what to do first if you have no heat at night in Columbus, OH, our night-time guide walks through the same three checks.
Repairs are diagnosed on site and the price is quoted before work begins. The average furnace repair in Columbus costs $304, according to Angi, with most jobs landing between $123 and $505. For more detail, see our furnace repair cost in Columbus, OH page and our guide to what a furnace repair should cost.

How do I stay warm and safe while waiting?
While you wait for heat, close off unused rooms and hang a towel at the bottom of exterior doors to slow heat loss. Dress in layers and use blankets. To protect pipes, let faucets on exterior walls drip slowly and open the cabinet doors under sinks. If you use a space heater, keep it at least three feet from bedding and curtains, put it on a flat floor, and never leave it running unattended or while you sleep. If the power stays out and the house keeps cooling, pipes can freeze — see what to do when furnace failure leads to frozen pipes in Columbus, OH. For the full safe-heat method, see how to stay warm without heat in Columbus OH.
Never run a portable generator indoors — not in the house, not in the garage, not even with the door open. Generators produce carbon monoxide, an odorless gas that can kill in minutes. A generator belongs outside, at least 20 feet from the house, with the exhaust pointing away from windows and doors. Never use a gas oven, grill, or fire pit to heat your home. If you smell gas or the carbon monoxide alarm sounds, get everyone outside and call 911 from outside. Our guide to carbon monoxide safety for gas furnaces explains what to check. Once the heat is back, a furnace tune-up in Columbus, OH is worth booking before the next cold snap.

Most furnaces that won’t start after power outage, Columbus, OH, just need the breaker, the switch, or the thermostat put right — ten minutes of checks before you call. If those checks don’t bring the heat back, our technicians are available 24/7 at (380) 273-8167 across Columbus and 13 suburbs, servicing 7 furnace brands.
Frequently Asked Questions
Why won’t my furnace start after a power outage?
A furnace won’t start after power outage, Columbus, OH, most often because of a tripped furnace breaker, a furnace power switch that was flipped off, or a thermostat that lost power or its settings. Check those three first. If the furnace still will not start, it may be in lockout — call (380) 273-8167 for 24/7 help.
Do I need to reset my furnace after a power outage?
Usually not — a healthy furnace restarts on its own once power, the breaker, the switch, and the thermostat are all correct. If it is locked out, one reset is safe to try: switch off, wait 30 seconds, and switch back on. If the fault returns, stop and call a technician.
How long can a house go without heat after an outage in Columbus?
It depends on the temperature outside, your insulation, and your pipes — but a house cools steadily, and pipes are at risk when it stays below freezing. Let faucets drip, open sink cabinets, and call (380) 273-8167 for 24/7 help if the furnace will not restart.
Can I run a portable generator to power my furnace?
Never run a portable generator indoors, in a garage, or near windows and doors — generators produce carbon monoxide, which is odorless and can kill in minutes. A generator belongs outside, well away from the house. Never connect one directly to your home wiring unless a licensed electrician has installed a transfer switch.
2 Responses